Hondavert KPro daughter board for Honda Civic, S2000 and Acura RSX ECU, which significantly expands capacity of it.
Datalog, RealTime Programming, Launch Control, Boost Control, Nitrous Control and more.
Fully retains all vehicle systems. ABS, Gauges, Climate control and etc.

Hondavert KPro compatible with the following cars

  • Acura RSX/ Honda Integra
  • 2002-2004 RSX (Type S) (PRB ECU)
  • 2002-2004 RSX (Base 5 speed) (PND ECU)
  • 2001-2006 DC5 Integra Type R (PRC ECU)
  • 2005-2006 RSX (Type S)
  • Honda Civic
  • 2001-2005 Civic (DX, LX, HX & EX with D17 only manual gearbox)
  • 2002-2005 Civic Si (PNF ECU)
  • 2003-2004 Civic Type R (PRD ECU)
  • 2002-2005 Civic Type R (PRA ECU)
  • Honda S2000
  • 2000-2005 S2000 (need some sensors modification)

What sotware can I use?

All Hondavert KPro board versions works with KManager 4.2.3. Also KPro board version 1.6 and more moderm also works perfectly with KManager 4.4.4.
Non recommended software used for tuning will brick the boards and has to be shipped back for repair, charges applied for repair.
To avoid repair charges please use Manager 4.2.3 or KManager 4.4.4

>>>Download KManager 4.2.3 PORTABLE<<<

Under construction


If you do not understand what written here – then you should not do this!
Send ECU to us – we will install board for FREE!

Hondavert Team

To install the board you need some tools and parts:

  • Soldering station and soldering iron
  • Hondavert KPro board
  • KPro installation kit (come with the original product)

All full sized pictures available here

>>>Download images [55 Mb]<<<

Open ECU case. The ECU inside should look similar to the picture.
We need to modify five components: CN2, CN3, J270, J250, R243
Desolder R243 marked as «0» and Solder another one from KPro Installation pack
Find J250. Solder a jumper
Desolder location J270 and solder with supplied pin from installation pack
Desolder location CN2 and solder with supplied pins from installation pack
Desolder location CN3 and solder with supplied pins from installation pack
Make two jumper wires between soldered CN3 pins and «holes» on the board as shown above
Make a jumper wire between soldered CN2 pin and «hole» on the board as shown above
Make another two jumper wires between soldered CN2 pins and «holes» on the board as shown above
Control youself: Total we make five jumper wires
Make a hole in ECU case for USB Connector
Install the ECU board to ECU case. Do not screw up two marked screws.
Install KPro Board with supplied screws from installation pack

FIRST TIME USAGE: Make “ERASE ECU (Clean protection)” from “ONLINE” menu of KManager software.

WARNING! Before you start. Please understand ONE simple thing. Hondavert KPro is NOT a fake copy/counterfit/replica of Hondata KPro Board. It is own development Board with COMPATIBLITY of Hondata KManager software. Yes it’s has full compatibility with Hondata KPro V2 hardware, but she has other functionality that Hondata does not. Understanding this simple thing, we come to the understanding that our board is NOT Compatible with all versions of Hondata KManager software from Hondata’s web site.

By default all Hondavert KPro boards versions works with KManager 4.2.3 with disabled internet updates. Please download if from www.hondavert.ru “Download” tab.

>>>Download KManager 4.2.3 PORTABLE<<<

What differences between snandard and PORTABLE version?
-Does not require installation. Works from a flash drive or any folder on your hard drive.
-At startup, automatically set the correct date for KManager. -Checks and disables “Automatic Updates” before each launch of KManager
-Associates files with itself on every launch

How to use?
Unpack it into any folder. Run it at least once. The program will do all for you.
Be sure to first click on the tooltip at the bottom left, which suggests installing the driver.


There are D1 RED and D2 BLUE LEDs near the USB connector
D1D2Meaning
OfOnNormal operation when not connected to KManager.
-Ignition ON and USB Disconnected
-Ignition OFF and USB Connected
Blinking
Slowly
OnKManager communicating with the KPro Board normally. (Dataloging
or Programming not Active)
Blinking
Fast
OnKManager Datalogging from ECU.
OnOnKManager Programming ECU.
OnFlashingFault with programmer board
OffOffIf the ignition is ON, then there is a fault with the programmer board or
ECU socketing.

Under construction

Under construction


Software and Utilites

Virtual machine

PDF instructions (updates discontiniued)